Can I use a chainsaw to dig a trench? Yes! … 1) They’re easy to maneuver – A chainsaw is lightweight and compact which means it is easier than ever before to dig deep into your yard without having to worry about any heavy equipment getting in your way.

Can you use a chainsaw in dirt?

Don’t Cut Into Dirt Nobody plans to run their chain saw into dirt. … In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch. Plus, dirt wears the sprocket at the bar tip.

Can I dig my own trench?

Digging a trench down to your sewer line is mostly just a matter of hard work. It is not technically difficult, but it can be extremely demanding physically. No materials are required, and the tools are simple ones that many homeowners already have on hand or can rent.

What is the best tool to use to dig a trench?

Trench Digging Shovels are used for digging narrow flat-bottomed trenches 4 inches wide, and up to 18 inches deep. They are also called step-trench shovels because the upturned back surface lets you push down (step on) the shovel with the toe of your boot while it is in the trench.

How do you manually dig a trench?

Begin by excavating the trench with a trenching shovel. Use a pick mattock to remove rocks, chop roots, and breakthrough tough ground. Pull loosened dirt out of the trench with a hoe. Check the trench depth, width, and slope to make sure it is uniform.

Is it OK to use a chainsaw on wet wood?

No, it is not bad to cut the wet wood with your chainsaw. Dewdrops, raindrops, or the snow on the wood will not cause any harm to your chainsaw. It is, in fact, much easier to cut through the wet wood than dry wood because the extra moisture on the wood will act as a natural lubricant.

How much does it cost to dig a trench?

Equipment (Trencher)$1.75 – $2.50Labor*$2.25 – $9.50Total Per Linear Foot$4 – $12Total Per 100 Linear Feet$400 – $1,200

What happens if you run a chainsaw without bar oil?

No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.

How quickly does a chainsaw get dull?

When you consider how fast the chain is moving, it’s not hard to understand that it can become very dull very quickly. Just hitting one little rock can dull a chain instantly. Like DavidV said, get yourself a new chain, keep it out of the dirt and sharpen it after every tank of gas to keep it from getting dull.

How deep will a Ditch Witch dig?

Our depths range from 12 inches up to 48 inches.”

Article first time published on

What is a trencher shovel?

Trenching shovels are designed for, you guessed it, digging and clearing trenches. They feature a sharp, pointed tip and squared sides to produce clean trench walls and minimize disruption of the surrounding soil.

How far down is a sewer line?

The depth of sewer lines varies greatly. They can be as shallow as 12″ to 30,” or as deep as 6+ ft. Often times this is simply a matter of climate. In really cold climates, the pipe is buried deeper to prevent the pipe from freezing solid in winter.

What is code for buried electrical wires?

Low-voltage (no more than 30 volts) wiring must be buried at least 6 inches deep. Buried wiring runs that transition from underground to above ground must be protected in conduit from the required cover depth or 18 inches to its termination point above ground, or at least 8 feet above grade.

How deep are electric lines buried?

In addition, National Codes dictate the depth, below ground, these lines must be buried. Some low voltage underground circuits could be as shallow as 18 inches, while most higher voltage circuits will be deeper than 24 inches.

How much trench Can you dig in a day?

Trencher Production “That’s one trench with one operator, opening up 10,000 feet of trench per day, whereas one excavator can open up 1,000 to 1,500 feet per day.

How do you slope a trench?

For example, if the trench is 6 ft deep and 20 ft wide across the end of the trench and the bottom of the trench is 2 ft wide, the slope can be calculated as follows: Horizontal distance = 20 ft – 2 ft ÷ 2 = 9 and the Vertical depth = 6 ft; Slope = 9 ÷ 6 = 1.5 to 1, which is the slope needed for type C soil.

How long does it take to dig a trench with a trencher?

It took me about 30 minutes to actually dig the trench. It took longer to load, transport the trencher, and unload it than it did to use it. It also took longer to clean it after I used it than to dig the trench. I ended up paying for a half days rental.

How long does it take to dig a trench with a backhoe?

Dug, pipe laid and backfilled about 11 to 13hours, only digging can be done in 9 hours or so. We average 280-300 ft per hour digging a 48″ deep trench with an excavator putting in non grade lines to pivots.

How do you calculate trench excavation?

Determine the volume of the trench by using the formula: Volume = Width x Length x Depth. As an example, a trench 12 feet long with an average width of 2.3 feet and an average depth of 5 feet has a volume of (12 x 2.3 x 5) cubic feet.

Why do chainsaws smoke?

While a chain saw does produce some heat while in use, it should never overheat or begin smoking. … The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.

Why do chainsaws leak bar oil?

What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.

Can you use a chainsaw in water?

No, you can not run a chainsaw in the water. You can work in the rain and wetlands, but you cannot submerge a regular chainsaw underwater to cut anything under the water surface. If you submerge a gas-powered chainsaw underwater, the water will get into the engine and ruin your chainsaw.

How long should a chainsaw chain stay sharp?

A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.

How often should I flip my chainsaw bar?

Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.

Why does my chainsaw cut curves?

Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.

Can I use WD40 as chainsaw oil?

No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant since it’s primary use is as a solvent or rust dissolver.

What's the difference between chainsaw bar oil and regular oil?

Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.

Why does my chainsaw blade go dull so fast?

Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.

Will a trench digger cut through tree roots?

Avoid using a trencher to cut through large tree roots if possible since larger roots increase the likelihood of problems with the cut. Although a trencher can be used to cut through roots, it was designed for creating trenches in soil and may not be able to handle large roots.

How wide of a trench does a Ditch Witch make?

At only 32″ (813 mm) wide, the Ditch Witch 1030 walk-behind compact trencher can go anywhere and dig in any type of dirt, thanks to the variety of digging chains it can run, including the patented, super-durable Shark Chain II trencher chain.

What is a Ditch Witch trencher?

Ditch Witch Introduces Heavy-Duty Trencher with Purpose-Built Design Features for Superior ROI. … And a hydrostatic trencher-chain drive with an infinitely variable displacement motor allows operators to easily match chain speeds to soil conditions.