Crowfoot wrenches are open-end sockets that come in handy when reaching around obstacles. They work where common 6pt and 12pt sockets and wrenches simply cannot fit. … The crowfoot wrench above is shown attached to a ratchet with a short extension for extra reach.

What is a combination wrench?

Definition of combination wrench : a wrench with one open end and one socket end.

What is a butterfly wrench?

A butterfly is a type of impact wrench that operates on the same principal as a standard impact wrench. … The butterfly wrench uses a flat paddle on the body that can be tilted in one direction by the user to make the wrench turn in a tightening direction.

What are flare nut wrenches used for?

Obviously, flare-nut wrenches are best for tightening or loosening hexagonal nuts and fittings. This makes them versatile and useful, especially for working on cars or plumbing. The most popular industry to use flare-nut wrenches is the automobile industry.

Does using a crows foot change torque?

If you place the crowfoot wrench at an angle 90-degrees to the torque wrench handle, the amount of torque you’re applying doesn’t change. You can set the torque wrench to the fastener’s torque specification and continue to use the torque wrench normally.

What is 90 degrees on a torque wrench?

90° = quarter turn. 180° = half turn. It’s alright if you are off a few degrees.

How do you calculate torque with a crow's foot?

In example E, the offset is 1.25 inches because of the crow foot wrench being used. The torque wrench length is this example is 13.5 inches. (13.5 x 180) / (13.5 + 1.25) = 2430 / 14.75 = 165 ft.

What is spud wrench?

Spud wrenches have a tapered spike at the handle end that’s used to align bolt holes when installing automotive components, beams, girders, or pipe fittings. The opposite end comes with a wrench to rotate fasteners for installation or removal.

What does a box end wrench look like?

Box-end wrenches have ends that enclose the nut and have 6, 8, 12, or 16 points inside the head. … Early box and socket wrenches fit only a particular nut or screw with flat surfaces on the head. The open-end wrench may have rectangular slots on one or both ends.

What are star wrenches called?

Torx (pronounced /tɔːrks/) is a trademark for a type of screw drive characterized by a 6-point star-shaped pattern, developed in 1967 by Camcar Textron. A popular generic name for the drive is star, as in star screwdriver or star bits.

Article first time published on

Is a crescent wrench a monkey wrench?

Crescent wrenches have one fixed jaw and one movable jaw; they differ from monkey wrenches in that the jaws on a crescent wrench are nearly parallel to the handle, whereas the jaws on a monkey wrench are perpendicular to the handle. In both types, the jaws are adjusted using a worm gear that you turn with your thumb.

Where should flare nut spanner should not to be used?

Unlike 12-point ring spanners, 12-point flare nut spanners are not suitable for use on square fastener heads.

Is a flare nut wrench the same as a line wrench?

Brake line wrenches (flare nut wrenches or simply line wrenches) serve a specific purpose. Domestic cars often use 7/16-inch and imports 10 mm. Brake line wrenches (often called flare nut wrenches or simply line wrenches) serve a specific purpose in a mechanic’s toolbox.

What does a flare nut wrench look like?

Flare nut wrenches are a type of open-ended wrench that’s intended for use with hexagonal nuts and fittings, which are sometimes referred to as flare fittings. Visually, they resemble box or ratchet wrenches but with an open head instead of a closed loop.

What is ancillary indication?

For those of you who have never heard of a directional ancillary indicator, it is a simple tool, used mainly in the outdoors, that helps you tell direction. … Your multi-tool helps you to prepare for any situation, from mechanical mishaps, to outback survival, to just having a drink with your mates on the weekend.

How often do torque wrenches need calibration?

In short, it’s standard practice to calibrate your torque wrench every 5,000 cycles or every 12 months, whichever comes first.

Which type of torque wrench is best used to determine breakaway torque?

BREAKAWAY TORQUE / ANGLE The breakaway is the preferred method for the measurement of residual torque. With this strategy, a digital torque wrench applies torque to rotate the screw further, and measures the torque at the point where the screw starts moving.

Is a torque wrench?

A torque wrench is a tool used to control and apply a specific torque to a fastener such as a bolt or a nut. It is a fundamental element in general mechanics, tire changing operations and industrial maintenance & repair industries, to ensure customers’ safety.

How much torque do you lose with a swivel?

Because torque wrenches are measured by direct turning force, you may need to increase the torque wrench setting by 10 to 15 percent when tightening a fastener with a swivel socket.

How do you calculate torque wrench?

1. M1 is the torque setting of the wrench.
2. M2 is the actual torque applied to the nut.
3. L1 is the normal length of the wrench.
4. L2 is the extended length of the wrench.

What is torque angle?

Put into its most simple terms, torque angle replaces a maximum torque value for a fastener with a specific amount of fastener rotation. After setting a low baseline torque, just to make sure the fastener is set, the fastener is rotated a precise amount to set the final position and clamp load.

What is a torque to yield bolt?

What is a torque-to-yield bolt? It is a one-time-use fastener that is designed to stretch during the torquing process (installation). Because of this stretching, the integrity of the bolt is compromised. These bolts cannot and should not be reused due to the stress caused to the bolt during its first installation.

What is a curved wrench called?

Basin Wrench It has a long, T-shaped handle with a curved jaw that looks like the top of an “S.” It is used to work on fixtures under sinks and toilets, hence why it is also called a faucet wrench.

Why do they call a pipe wrench a monkey wrench?

Charles Moncky, a Baltimore mechanic, invented the monkey wrench around 1858. Moncky’s wrench was named using a purposeful misspelling of his name. … Stillson, a steamboat firefighter, received a patented on September 13, 1870 for an invention later known as the Stillson pipe wrench.

What does a monkey wrench look like?

A monkey wrench has been described as having both an L- and F-shaped appearance. Basically, the monkey wrench has a fixed upper jaw with a lower jaw that can move up and down the wrench through a screw mechanism. … Conversely, if you want to loosen a fastener, turn the monkey wrench counterclockwise.

What is the difference between an open end and a box end wrench?

They come either separately or in a combination form, with one end being an open wrench, while the other is boxed. The box end has a tendency to slip off, while the open end allows more versatility since it needs only to contact two sides of the nut or bolt.

What is the largest crescent wrench?

Overall Length30.0 in.762.0 mmWeight12.17 lbs.5520.22 g

Why are construction wrenches pointy?

During assembly, the bolt holes don’t necessarily line up, so you stick the tapered tail through the mating holes in the construction item, lever them around till the adjacent holes line up, slap a bolt through, affix a nut and washer and then use the wrench end to tighten.

What is a chain wrench?

Noun. 1. chain wrench – another name for chain tongs. chain tongs – a pipe wrench used for turning large pipes; an adjustable chain circles the pipe with its ends connected to the head whose teeth engage the pipe.

What is Torx key?

Torx keys are also commonly known as star keys. Like hexagon allen keys, most torx keys are small enough to be carried in a pocket and enable the user to drive the appropriate fasteners without needing a separate screwdriver or power tool.

Are star and hex the same?

Hexagon keys are also known by several other names including hex key, hex wrench, Allen key, and Allen wrench. … The generic name given to Torx fasteners and keys by the ISO is hexalobular, although virtually no one uses this name. Instead they will more commonly be referred to by the generic terms “star” or “six-point”.