The Porter bee escape was first used in the 1890s and was a single ended metal device that would allow bees to go only in one direction. The escape was placed in an oblong hole and had a hole that was approximately 7/8” in diameter on top.

How do you use a Porter bee escape?

Porter in 1891 The basic principle of its use is simplicity itself – a one way valve. Place the escapes in the crownboard slot/s with the top hole uppermost. Check that the springs are 3mm apart. This supplies just enough tension for the bees to pass through yet are close enough together to prevent their return.

How do Quebec bees escape?

Just place under your honey supers with the triangle side facing down. The bees will exit and can’t get back in. Leave it on overnight. It’s a passive way to separate the bees from your honey supers.

Do Porter bee escapes work?

Porter bee escapes make for a slower clearer board but when correctly set they will not allow the bees to get back up again. Unfortunately they often get a bad press but if they are set up carefully and a few precautions are taken to maximise success – they’re brilliant, clearing supers 95% of the time without a fight.

Why do bees escape?

The bee escape is used to empty the bees out of the honey supers that you want to harvest. … Once you’ve harvested your honey, you can either put your honey super back on the hive with empty frames, place new frames in the hive or leave the bee box off for the rest of the year.

How long does it take for a bee escape to work?

Besides being a relatively slow process (usually 24 to 48 hours for complete removal of bees) the use of bee escapes requires caution: If left on the hive for more than about 48 hours, the bees will eventually learn their way back into the supers.

How does a rhombus bee escape work?

The Rhombus shape allows bees to descend rapidly, whilst preventing re-entry. Simply attach the escape to the top of your crown board, and place beneath the supers ready to be cleared of bees.

How long does hive clearing Board last?

Takes about 10 minutes per box.

What is a hive crown board?

The crown board is a method of closing off the top of a bee hive so that the main protective roof can be easily removed. The Grain should run along the longest dimension of any part.

When would a beekeeper use a bee escape?

Before a beekeeper can harvest, they must gently remove these loyal workers. Rather than pull combs one at a time and brush off bees, only to watch them land on the comb again, the bee escape allows you to remove bees from your honeycomb without disturbing the colony.

Article first time published on

Which way does a bee escape board go?

Place the bee escape board, correct side up, on top of the brood boxes. Make sure that it is flush, and there are no gaps. Place honey supers on top of the escape board. Overnight, the bees in the honey supers will go down into the brood box to be with the cluster.

Who invented the honey extractor?

Major Franz Elder von Hruschka invented the honey extractor in the winter of 1864/1865. He was born in Vienna and resided near Venice.

How do you clear a Super Bee?

To blow bees out of honey supers, simply remove the honey super filled with bees from the hive and place it up on its end on a bench, table, or back of a truck. By directing air from the blower between the frames, the bees are blown out of the super.

What is a clearer board?

The term Clearer board (or Escape board) refers to a device that helps remove the bees from the honey super. The “exit” or “escape” is a metal corner fitted to the board that allows the bees to exit.

What is a Crown board for?

Crownboards cover the hive under the roof and are typically ply with one or two holes designed for feeding and/or Porter bee escapes. Since the most basic function they serve is to prevent the roof being propolised down they can be as simple as a sheet of thick polythene cut to size.

How do you use a bee maze?

The Bee Maze is a great device for getting bees out of supers. Place the bee maze under the capped honey with the screened triangle facing down. The bees can move down out of the super, but they can’t return. The weather will determine how quickly the super is cleared out.

How do you place an escape board?

Place the escape board under the super you are removing with the triangle side face down. Replace the honey super, inner cover and outer cover. Leave the escape board on overnight to allow the bees time to leave the super. Once the honey super is empty, it can be removed from the hive along with the escape board.

What is a tangential honey extractor?

Tangential honey extractors have the frames held in the basket with the honeycomb facing outwards. It allows for complete removal of honey from one side of the frame at a time. Tangential honey extractors can be found in use by many beekeepers.

What is the Number 1 thing you need to do to ensure your bees survive winter?

Maintain the Cluster for Winter Survival The most important one is making sure the honey bars are positioned so that your bees can easily eat through them, in order, without having to try to move across honey-less sections of the hive.

What is the use of honey extractor?

A honey extractor is a mechanical device used in the extraction of honey from honeycombs. A honey extractor extracts the honey from the honey comb without destroying the comb. Extractors work by centrifugal force. A drum or container holds a frame basket which spins, flinging the honey out.