A bath and shower diverter is a device that diverts the flow of water either toward the tub spout (i.e., to the bathtub) or toward the showerhead. This product is commonly found in bathtubs equipped with a showerhead, such as in residential bathrooms and private commercial restrooms found in hotels.

What is the difference between a diverter and non diverter tub spout?

A diverter tub spout is designed with a mechanism inside that allows water to flow upward, which creates the necessary pressure to start a shower. … A non-diverter tub spout, by its very name, works in the contrary direction of a diverter type tub spout.

What type of tub spout do I have?

How To Determine What Type of Tub Spout You Already Have. Grab a flashlight and look beneath the tub spout while it still attached to the wall. If you can see a tiny screw on the underside of the spout, you have a slip-on tub spout with a set screw. If there is no set screw, you have a threaded tub spout.

What is the purpose of diverter?

Diverter valves switch the flow of water between the tub faucet and the showerhead. Water flows directly through the faucet and into the bathtub when the valve is open. When the valve is closed, water pressure forces the water to run upward to the showerhead.

How does a pull down diverter tub spout work?

The diverter pulls down easily, and seals perfectly (no leaking water out of the spout while the shower is on). When the water is turned off, the decreased pressure lets the diverter automatically pop back up, so the next time you turn the water on you don’t get an unintentional shower.

Do you have to turn off water to change shower diverter?

If you’re only working on the diverter, you don’t need to turn off the water supply to the faucet. While working, place a cloth over the tub drain to prevent any dropped screws from going down the drain. Some showers use a diverter built into the tub spout activated by lifting a button on the spout.

Do you need a diverter valve?

Shower diverter valves can be a fairly confusing part of the shower build process. Without one, you aren’t going to have any ability to redirect the flow of water. Even if you have a simple setup with just a tub faucet and a showerhead, you’ll need a diverter valve to switch between them.

What is pull-down diverter?

Pull-down diverter adds convenience to your tub. Polished chrome finish adds a sleek touch to your bathroom. Backed by a limited lifetime warranty for your satisfaction.

What is a slip fit tub spout?

A slip-fit spout has an internal assembly that slips over a copper pipe. The spout has an opening on the bottom side where a setscrew is tightened to hold the spout onto the copper pipe. A slip-fit spout does not contain threads.

How does pull-down diverter work?

The diverter pulls down easily, and seals perfectly (no leaking water out of the spout while the shower is on). When the water is turned off, the decreased pressure lets the diverter automatically pop back up, so the next time you turn the water on you don’t get an unintentional shower.

Article first time published on

Where is the diverter valve?

It’s usually a lever that’s situated behind the bath taps that you can pull up or push down. System and conventional boilers don’t require a diverter valve. This is because the hot water they produce is stored in a hot water cylinder.

How much does it cost to replace a shower diverter?

PartAverage cost to replaceShower diverter valve$225 – $575

Do you need to caulk around tub spout?

Missing or damaged caulk around a slip-on tub spout can allow water to begin to seep behind the walls, damaging the interior of the wall and possibly creating an environment that fosters mold growth. You must remove the old caulk before applying a new bead of caulk around the tub spout to ensure proper adhesion.

What does a shower diverter look like?

The diverter looks like a pin pulled upward from the bathtub faucet spout. It’s possible that it may come in the form of a third handle or a button that needs to be pushed or pulled. Either way, when the valve is activated, it engages a rubber stopper, which causes the water to flow in a different direction.

How do you put a shower diverter back in?

1. Replace the Diverter Stem Of a Front-end Spout. Step-1: Insert the Diverter Stem. Step-2: Align the Diverter Gate Properly. Step-3: Push the Diverter Gate.
2. Replace the Diverter Stem In a Three-valve Shower. Step-1: Open Up the Middle Knob. Step-2: Remove the Escutcheon. Step-3: Remove and Reinstall the Diverter.

Can a shower diverter be repaired?

Once you’ve determined that your shower diverter is broken, don’t delay in repairing it. Though it might be an easy task to put off, a broken shower diverter wastes water and creates a poor shower experience. Repairing a shower diverter is a home improvement project that you can complete in just one day.

How do I find my shower diverter valve?

If the faucet has three handles, it is a rare three-handle model. The third handle works as a diverter, projecting the water flow either to the showerhead or to the bathtub fixture. If there are no handles but a series of buttons on a large panel, the faucet is a panel shower.

Can you use a shower and tub valve for just a shower?

Can a tub and shower faucet be used just for a shower? … Most tub and shower combination faucets can be installed in a shower without using the tub spout. If you do not wish to use the tub function, you can plug the outlet for the tub spout on the valve and not install the spout on the tub wall.

Does it matter what order you turn off the faucets shower diverter?

After you find the right combination of hot and cold water, you turn the third handle clockwise to send the water to the showerhead. When you’re done showering, turn the handle counter-clockwise to redirect the water to the tub.

How do you replace a shower diverter valve?

1. Unscrew the set screw. See how the spigot is attached to the wall. …
2. Unscrew spigot from the wall. Be careful! …
3. Wash Supply Pipe. Make sure that you clean off any bits of gunk from the supply pipe. …
4. Replace new spout on the copper pipe. …
5. Test it and make sure it works!

How long does it take to fix a shower diverter?

It may be a simple job to put off, a damaged shower diverter wastes water and creates a bad shower experience. Repairing a shower diverter is a DIY job that you can complete in simply one day.

Why is my tub diverter not working?

The most common issue with a shower diverter is when water comes out of both the tub faucet and the showerhead. Check to be sure there is no residue clogging the shower diverter lever from fully lifting or lowering. If everything looks clear, the problem could be worn-out parts in the shower diverter valve.

Why does tub faucet leak when shower is on?

A leaky shower diverter. A diverter may be an unfamiliar term. The diverter is a valve in your tub’s faucet that diverts water from the tub to the showerhead when the lever is pulled to turn on the shower. A small amount of water dripping out of your tub’s faucet is normal because the valve doesn’t have a perfect seal.

Can you use sharkbite for tub spout?

Use the Sharkbite Shower/Tub Installation Kit, which push-connects onto 1/2″ hard copper between the valve and the spout. … The 3/4″ PEX crimp fittings may have a larger internal diameter than the 1/2″ Sharkbite as well.

How does the bathtub spout work?

A metal rod enters the tub spout from the top and clips on to the plastic gate. When the rod is pushed down, the gate lies below the water supply pipe, allowing water to flow freely from the tub spout. When the rod is pulled up, the gate lifts and covers the flow of water.

Are tub faucets universal?

There is no specific reason bathtub faucets are not universal besides the fact that different contractors install different types of bathtub spouts when building the bathroom. So, ultimately, it all depends on how your bathtub is built.

How do you remove a stubborn tub spout?

The first step is to cut through any caulk between the spout and wall. Then grip the spout near the wall with a 10-inch pipe wrench and try again with a little more gusto. Push counter-clockwise, using steady pressure. If that approach doesn’t work, you’ll need to cut off the spout with a hacksaw.

What is a shower diverter?

If you have a shower-tub combination in your bathroom, the shower diverter valve is what allows you to divert the water back and forth between the tub faucet and the showerhead. Though they are typically very simple devices, shower diverters may malfunction and need replacing once in a while.